A complete kit for protecting your valuable daggerboard:
4 rubber inserts, adhesive, sandpaper and 4 self adhesive glide strips
( 300 x 18 x 1,0 mm each). These strips can be stuck to the top and the
bottom of the case and minimize play and friction between the dagger-
board and its case.
EX1117 Complete daggerboard protecting kit as described above
EX11171 Roll of 8 m glide tape
EX1116 Rubber insert only, 1 pc
EX1116-10 Rudder insert only, 10 pcs
daggerboard protection
EX1117
EX11171
18
Full batten top cover.
This cover has 2 sailbattens integrated in the top
panel. The top panel will be tented when the webbing straps connected to
both ends of each batten are tensioned. Made of Grey 600D pvc coated
polyester. The padded panels on the front back and sides fold around the
corners and protect your hull. This design allow you to
remove the battens from the cover quickly.
Each batten can be disconnected in the middle for easy storage.
EX1080 Padded full batten top cover
Breathable top cover.
Made of Moistureguard 2000, a heavy duty 900D
polyester with a polyurethane membrane which has excellent
breathability and is water-resistant. Wide skirts around the edge of the hull
for good protection. Fast and easy to install with two straps
with two adjustable quick-clip buckles.
EX1081 Breathable Moistureguard topcover Color: Light grey
Low cost topcover.
Design like EX1081 but made of 600D pvc
coated polyester.100% water resistant but not breathable. Color: Light
grey
EX1082 Optiparts topcover “economy”
Economy undercover.
Design like EX1091 but made of 600D pu
coated polyester. Color: Light grey (only for traveling)
For outside storage use EX1091.
EX1091S Optiparts “economy undercover”
Breathable undercover.
Made of Moistureguard 2000
Quick and easy to install with a 6 mm shockcord in the skirt and 2 straps
with quick-clip buckles. With 3 wide strips of thick foam in the bottom to
protect the hull (even from concrete) while being rigged. Color: Light grey.
EX1091 Optiparts undercover of “Moistureguard 2000”
Fully padded undercover.
Provides the best possible protection
during travel. 420 PU outside, new higher quality 190T interlining inside
and closed cell foam in between. (only for traveling)
For outside storage use EX1091.
EX1095 Optiparts fully padded undercover
Covers
EX1080
EX1082
EX1081 (NOT SHOWN)
EX1091
EX1095
EX1091S
Hull protectors
BOW BUMPER. Foam tubing covered by heavy duty polyester cloth.
This fender has a snug fit around the bow of the Optimist.
Ideal for sailing schools. With grommet in the middle to pass the painter.
For instructions see:
EX1065 Bow bumper
CORNER PROTECTORS. Heavy duty rubber corner protectors with
self adhesive backing. These can be used on bow only or on all 4 corners.
Special preshaped rubber profile. This is not a flat piece of thin rubber!
EX1066 Corner protectors
=Set of 2 pieces=
EX1065
EX1066
Notice: Remove top covers during transport.
Complete package of Optimist protection for maststep, daggerboard,
mast, outhaul, bailer and sprit.
Contains self adhesive ptfe protection for maststep, outhaul, daggerboard,
sprit, rudder, bailer and boat corners. Also contains 5 ptfe mastsep coins
and rubber daggerboard slot inserts.
EX1118 Protection pack
protection pack
EX1118
VIDEO
PDF
MANUAL
